MDS MDS 9710 Series Specifiche Pagina 53
- Pagina / 58
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
05-3305A01, Rev. D MDS 4710/9710 I/O Guide I-1
INDEX
A
ACCESS DENIED error message 17
Accessories 4
Accessory Power pinout (Pin 18) 11
Active messaging (defined) 41
Alarms
alarm code definitions 31
major vs. minor 30
pinout (Pin 25) 11
using STAT command to display 28
AMASK command 19
Antenna
installation 6
RSSI command used to refine heading 12
system gain, defined 41
Yagi, illustrated 8
Antennas 8
Applications 2
Multiple Address Systems (MAS) 2
point-to-multipoint system 2
point-to-point system 3
ASENSE command 20
B
BAUD command 21
Baud rate
setting for RJ-11 DIAG port (DLINK command) 23, 35
Bit, defined 41
Bits-per-second. See BPS 41
BPS (bits-per-second), defined 41
BUFF command 21
Byte, defined 41
C
Cable, loss due to length of coaxial at 400 MHz 8
Cable, loss due to length of coaxial at 960 MHz 8
Carrier
Switched 3
Cautions
use attenuation between all units in test setup 35, 38
CKEY command 22
Codes, Model Number 3
Command Descriptions 19
COMMAND FAILED error message 17
Command summary, table 17
Commands
AMASK (set/display alarm triggers) 19
ASENSE (set alarm output state) 20
BAUD (set/display rate, encoding) 21
BUFF (set/display data handling mode) 21
CKEY (enable/disable continuous keying) 22
CTS (set/display CTS line response timer) 22
DATAKEY (enable/disable transmitter keying by radio) 22
descriptions 19–29
DEVICE (set/display radio behavior) 22
DKEY (deactivate transmitter after KEY command) 23
DLINK (enable/disable network-wide diagnostics) 23
DTYPE (set radio to root or node for diagnostics) 23
DUMP (display all programmed settings) 23
entering on Hand-Held Terminal (HHT) 16
Hand-Held Terminal (HHT) 16
HREV (display hardware revision level) 24
INIT (reinitialize radio to factory defaults) 24
INIT xx10 (restore standard transceiver defaults) 24
INIT xx20 (configure radio for use with P-20 chassis) 24
KEY (activate transmitter) 25
Keyboard 16
MODEL (display radio model number code) 25
MODEM (set modem speed) 25
OWM (set/display owner’s message) 25
OWN (set/display owner’s name) 25
PTT (set/display key-up delay) 25
PWR (set/display RF forward output power) 25
RSSI (display RSSI) 26
RTU (enable/disable internal RTU) 26
RX (set/display receive frequency) 26
RXTOT (set/display receive time-out timer value) 27, 29
SCD (set/display soft-carrier dekey delay) 27
SER (display radio serial number 27
SHOW (display DC voltage, data port, RF power) 27
SNR (display signal-to-noise ratio) 27
SREV (display software revision level) 28
STAT (display current alarm status) 28
TEMP (display internal temperature) 28
TOT (set/display time-out value and timer status) 28
TX (set/display transmit frequency) 28
Conversions, dBm-Watts-Volts 40
CTS command 22
CTS pinout (Pin 5) 10
D
Data Circuit-terminating Equipment—See DCE 41
Data Communications Equipment—See DCE. 41
Data interface
connector pinouts 10
display active connector port 27
installing connection 10
Data Terminal Equipment—See DTE 41
DATAKEY command 22
dB. See Decibel 41
dBi, defined 41
dBm, defined 41
DCD
LED 13
pinout (Pin 8) 10
DCE (Data Circuit-terminating Equipment), defined 41
Decibel (dB), defined 41
Description, product 1
DEVICE command 22
Diagnostic Channel Enable, pinout (Pin 23) 11
Diagnostics
interface specifications 33
network-wide, performing 34, 36, 38
PC software used for 37
using InSite software for network-wide 34, 36
- MDS 4710/9710 Series 1
- QUICK START GUIDE 2
- TABLE OF CONTENTS 3
- Antenna Installation Warning 6
- FCC Part 15 Notice 6
- 1.0 GENERAL 9
- 1.2 Applications 10
- 1.3 Model Number Codes 11
- 1.5 Accessories 12
- 2.0 INSTALLATION 13
- 2.1 Installation Steps 14
- 2.2 Transceiver Mounting 15
- 2.3 Antennas and Feedlines 16
- 2.5 Safety/Earth Ground 17
- 2.4 Power Connection 17
- (nominal) 19
- 3.0 OPERATION 20
- 3.1 LED Indicators 21
- 3.2 RSSI Measurement 21
- 4.0 TRANSCEIVER PROGRAMMING 22
- 4.2 Hand-Held Terminal Setup 23
- 4.3 Keyboard Commands 24
- Error Messages 25
- DATA INTERFACE connector 28
- Data Interface Port 29
- Baud Rate 29
- Continuously 30
- Initialize EEPROM 32
- Defaults 32
- Packaged Model 32
- Initialization 32
- DATA INTERFACE), before actu 33
- Received Signal 34
- Strength Indicator 34
- 5.0 TROUBLESHOOTING 37
- 5.2 Event Codes 38
- Event Code Definitions 39
- 6.0 TECHNICAL REFERENCE 40
- 6.2 Helical Filter Adjustment 41
- DATA INTERFACE 42
- Functions 44
- (MDS P/N 12-1307A01) 46
- 7.0 GLOSSARY OF TERMS 49
- Troubleshooting 29 55
- IN CASE OF DIFFICULTY 57
© 2020, manymanuals.it. Tutti i diritti riservati | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale